Contact Us / Log in or Sign up / Call us today! 520–392–9486, 8am – 6pm

Home » WooCommerce

WooCommerce

Visual Composer now includes WooCommerce specific shortcodes – easily drop in different sets of products.

Recent Products

  • The most economical way to install our foam technology on your walls or ceiling is to use our foam and the mounts. This allows for airflow on both sides as the mount pushes the foam 2″ away from the surface to allow for air floor. Foam and mounts are designed to work together.

    If foam pieces on your walls or ceiling are not acceptable, you can use our foam panel. It is our foam technology with a 3/4″ wood frame around its edge. It hangs flat against the wall and is installed using a single screw just like a picture frame. Wood frame can be painted any color. Foam is grey only.

    Foam panels come in four sizes: There are 19″ x 2″ x 27″, 26″ x 2″ x 56″, 38″ x 2″ x 56″, 56″ x 2″ x 75″

  • Amplifier/speaker cabinets produce energy, lots of energy. That energy leaves the amplifier and enters the room. Once in the room, it interacts with the room and excites all the relevant room modes. We must attenuate or absorb as much excess energy as we can as close to the source or cabinet as we can. This will insure a tight and defined presentation as the signal enters the room.

    Amplifier cabinets vibrate. The sound that emanates from the cabinet is the product of the speakers, electronics, and cabinet. If we reduce the cabinet vibrations, we allow the speaker and electronics to come through better. Our carbon amplifier platforms reduce vibration and absorb energy. It will provide you the one two punch you need to get the best sound out of your cabinet, speaker, electronics, and room.

    These are custom sized to your cabinet. You tell us the height requirement along with the cabinet width and depth. They can be painted or skinned with a wood veneer. We will custom build it to suit your individual requirements.

  • Speaker stands do many things for us. First, they separate the vibration of the speaker cabinet from our desk. Second, they allow the speaker to be the correct height. Third, they can provide broadband low frequency absorption in the area of the room that has the highest unwanted low frequency pressure. The front wall where our speakers are located is always an area of high frequency pressure.

    Achieving good sound in your room is about doing a lot of little things in the correct order. Reducing the vibrations of the speaker cabinet by setting it on a platform that is designed to absorb excess vibration and air born energy allows for the driver and the crossover to work together to produce energy without those cabinet resonances interfering. We use a damping compound layer that your speaker will sit upon.

    Using our carbon technology we achieve a platform that reduces cabinet resonances and also provides needed broadband absorption in the front of our rooms. This is the same technology used in our ACDA-10 and ACDA-12 units. Stands can weigh up to 50 lbs for the 12″ x 12″ version. The 12″ model will absorb from 30 – 50 Hz. and the 10″ deep unit will have broadband absorption from 30 – 200 Hz. The 8″ platform will start at 40 cycles and go through 200 Hz.

    Three widths are available. We have a 8″ x 8″ , 10″ x 10″, and a 12″ x 12″ model to accommodate different speaker widths and depths. Heights usually run around 30:” but you will have to tell us what height you desire. Finish is black paint enamel with 5 coats of paint hand sanded and clear coat sealed. Need a special width or height, just let us know.

    PRICING: 8 x 8 $375.00 10 x 10 $475.00 12 x 12 $575.00

  • Our carbon technology is now available for use in small rooms that don’t have the physical space requirements for our ACDA series to absorb lower frequency energy. Our carbon technology that has become so popular with our low-frequency product line is now available in panels that are not as deep as our ACDA units. With the same smooth frequency response starting at 40 – 60 Hz. and going through 6,500 Hz. it is a smooth low-frequency absorbing tool for absorbing unwanted low-frequency energy along the boundary surfaces in small rooms. At a maximum depth of 8″, it won’t take up much wall space and gives you lower frequency absorption down to 40 Hz.

    With carbon technology, you achieve a smooth absorption curve that is smooth in rate and level with a special quality of clarity that is not offered with foam or other absorption technologies especially the building insulation types that dominate the industry. If you are looking for a more natural rate and level of absorption that does not over absorb at certain frequencies and under absorbing at others, our carbon and foam technologies will give you that linearity you need.

    Our 24″ w x 6″- 8″ h x 55″ l unit is finished in a painted or wood case and your choice of wood and fabric color and texture are available. Units weigh 75 lbs and are designed to be hung on a wall just like a picture would be.

  • The QDA series of products incorporates the ultimate of everything in one product. We have quadratic diffusion, broadband and frequency specific absorption all wrapped in a furniture grade wood finish. It is our highest performing product and our most expensive.

    The QDA S series of product keeps the diffusion and part of the absorption and wraps it all in a MDF cabinet that is clear coated to prevent dirt and moisture impact. You get a prime number 11, 13 or 17 for the diffusion sequence and our ACDA -10 or ACDA-12 technology in the base. You can choose what type works best for your room and usage. You can choose broadband ACDA -10 absorption from 30 – 200 Hz. or more frequency specific absorption from 30 – 50 Hz. All units are on casters for easy positioning.

    With the QDA S series, you get your choice of diffusion and absorption type all in one unit in a cabinet that looks good but without the high cost of wood and paint finishes. The alder wood has a smooth and mellow tone quality that is equal to the more higher priced cherry woods.

Featured Products

  • Mockup of DIY Acoustic Treatment build plans package
    Mockup of DIY Acoustic Treatment build plans package

    FLASH SALE – OFFER ENDS IN
    Only $27 instead of $149.95!

    Having problems with the acoustics in your room? Need a cost effective way of dealing with absorption and diffusion? Then our all in one DIY Build Plan package is for you!

    You get:

    • 7 DIY Build Plans in one great value deal.You get a Broadband Diaphragmatic Absorber to manage your low frequency problems, Acoustic Panel plans to manage your mids and highs and 5 Sound Diffuser build plans to make your small room sound larger!
    • Each plan comes with a material and tool list, cut sheet and easy to follow step by step assembly instructions,
    • Actual build photos showing you what each finished step looks like,
    • Your solid wood BDA Bass Absorber unit, when built, will stand 24″W x 48″H x 10″D and bass energy all the way down to 40 Hz!
    • 5 Sound Diffuser Plans included (Metric & Imperial!).
    • DIY plans that are based on our $1,000+ production units!
    • Independently tested and predictable performance results,
    • Phone time with our Chief Acoustic Engineer Dennis Foley so any questions can be quickly answered,
    • Both horizontal and vertical diffusion options,
    • A 100% money back guarantee!
    Sale!
  • Image of Acoustic Foam sheets
    Image of Acoustic Foam sheets

    Tired of working with dead sounding foam? Want your vocals and music to shine without losing their emotion and energy? Then our unique Acoustic Foam is for you.

    More cells with better shapes produce more absorption below 500 Hz. In fact, we absorb 30% at 125 Hz. and 63% at 250 Hz. reaching 100% at 500 Hz. We went after the bottom half of the existing absorption curves to produce a foam that has a smoother absorption curve that goes lower where our vocals start and ends with a smoother, more gradual rate and level of absorption.

    You get:

    • More absorption below 250 Hz. than standard foams. It absorbs 30% at 125 Hz., 63% at 250 Hz. and 100% at 500 Hz.
    • Smoother absorption curve from 125 Hz. – 500 Hz. than any other foam on the market. This range is the heart of your vocal and music frequencies.
    • Technology that manages side wall reflections so you can hear the direct sound from your sources and not the reflected energy of your room.
    • Box of 4 foam tiles
    • Available foam sizes: 25″ x 18.5″ x 2″ | 25″ x 54″ x 2″ | 37″ x 54″ x 2″
    • Studio foam that lets your vocals and middle range instruments pop.
    • A technology that does not drain the life out of your room like so many other foams.
    • Foam that finally lets you hear the intimate timbre of the singers voice in every recording. Finally you will have a room that is an acoustical pleasure to record in and very much in demand.
    • A foam that comes with variable installation options.

    ALL PRICES FOR A PACK OF 4 FOAM SHEETS.

  • Acoustic Foam PFP Series
    Acoustic Foam PFP Series

    Tired of working with dead sounding foam? Want your vocals and music to shine without losing their emotion and energy? Then our unique Acoustic Panels are for you. You get:

    • More absorption below 250 Hz. than standard foams. The panels absorb 30% at 125 Hz., 63% at 250 Hz. and 100% at 500 Hz.
    • A smoother absorption curve from 125 Hz. – 500 Hz. than any other foam on the market. This range is the heart of your vocal and music frequencies.
    • A technology that manages side wall reflections so you can hear the direct sound from your sources and not the reflected energy of your room.
    • Each panel measures 27″W x 57″H and either 4″ or 3″ in depth depending on your preference.
    • A foam that lets your vocals and middle range instruments pop.
  • Activated Carbon Diaphragmatic Absorber image
    Activated Carbon Diaphragmatic Absorber image

    Are you tired of muddy and sloppy bass on your sound stage with bass notes blurring and smearing into one big bloated mess? Tired of not connecting with your music the way you know it’s possible? Frustrated by the lack of an emotional connection with your songs despite investing a crazy amount of money into your amp, speakers and hi-fi?

    Imagine being able to hear incredible bass separation and definition in every piece of music you play and enjoying the sound of your music coming to life as your mids and highs pop like you always dreamt possible. Imagine being able to experience crystal clear attack and decay in each individual bass note in every piece of music you mix or listen to.

    With the ACDA-10, you’re going to feel the power of every single bass note the way you want to hear it. It’s that connection to the music which makes all the difference to your enjoyment of it. It’s the dynamics and separation of instruments with crystal clear clarity definition, which creates the spine tingling, hairs on the back of the neck sensation that you desire so much from your mixing efforts and music collection.

    If you order the ACDA 10 today you will also get:

    • A free 30 minute phone or video consultation on your room mode issues with me, the products inventor, Dennis Foley
    • A 100% risk free 30 day money back guarantee
    • And castors so you can move the units in and out of your room if your listening room serves multiple purposes.
  • acda 10 Activated Carbon Diaphragmatic Absorber Cherry wood image
    acda 10 Activated Carbon Diaphragmatic Absorber Cherry wood image

    Are you tired of muddy and sloppy bass in your room with bass notes masking your music into one big bloated mess? Want to mix without second guessing what you’re hearing? Then our Activated Carbon Diaphragmatic Absorber is for you!

    You get:

    • The most powerful low frequency absorber available in the world today,
    • 100% absorption at 50 Hz., 63% at 40 Hz. and absorption all the way down to 30 Hz., all in a depth of just 16″,
    • Unprecedented attack and decay clarity in every bass note, so you can mix without second guessing,
    • A bass absorber that softens the mids and the highs,
    • A solid wood unit that stands 30″W x 60″H x 16″D,
    • Independently tested and predictable performance results as verified in this report by Riverbank Acoustical Labs,
    • Phone time with our Chief Acoustic Engineer so any questions can be quickly answered,
    • Expert placement advice so you can get the most out of your completed unit,
    • A 100% money back guarantee!

Top Rated

  • Mockup of a Acoustic Panel Foam DIY Plan
    Mockup of a Acoustic Panel Foam DIY Plan

    Are you tired of homogenous, ugly looking foam stuck up on your walls? Need a cost effective way of dealing with the problem? Then our DIY Acoustic Panels are ideal for you!

    You get:

    • A material and tool list, cut sheet and easy to follow step by step assembly instructions,
    • Actual build photos showing you what each finished step looks like,
    • DIY plans that are based on our $350+ production units!
    • Phone time with our Chief Acoustic Engineer so any questions can be quickly answered,
    • A 100% money back guarantee!
  • Image of Acoustic Foam sheets
    Image of Acoustic Foam sheets

    Tired of working with dead sounding foam? Want your vocals and music to shine without losing their emotion and energy? Then our unique Acoustic Foam is for you.

    More cells with better shapes produce more absorption below 500 Hz. In fact, we absorb 30% at 125 Hz. and 63% at 250 Hz. reaching 100% at 500 Hz. We went after the bottom half of the existing absorption curves to produce a foam that has a smoother absorption curve that goes lower where our vocals start and ends with a smoother, more gradual rate and level of absorption.

    You get:

    • More absorption below 250 Hz. than standard foams. It absorbs 30% at 125 Hz., 63% at 250 Hz. and 100% at 500 Hz.
    • Smoother absorption curve from 125 Hz. – 500 Hz. than any other foam on the market. This range is the heart of your vocal and music frequencies.
    • Technology that manages side wall reflections so you can hear the direct sound from your sources and not the reflected energy of your room.
    • Box of 4 foam tiles
    • Available foam sizes: 25″ x 18.5″ x 2″ | 25″ x 54″ x 2″ | 37″ x 54″ x 2″
    • Studio foam that lets your vocals and middle range instruments pop.
    • A technology that does not drain the life out of your room like so many other foams.
    • Foam that finally lets you hear the intimate timbre of the singers voice in every recording. Finally you will have a room that is an acoustical pleasure to record in and very much in demand.
    • A foam that comes with variable installation options.

    ALL PRICES FOR A PACK OF 4 FOAM SHEETS.

  • mockup of DIY Sound Diffuser qrd 7
    mockup of DIY Sound Diffuser qrd 7

    Suffering from poor diffusion in your room? Need a cost effective way of dealing with the problem? Then our DIY Sound Diffusers are for you!

    You get:

    • A material and tool list, cut sheet and easy to follow step by step assembly instructions,
    • Actual build photos showing you what each finished step looks like,
    • DIY plans that are based on our $1,000+ production units!
    • Independently tested and predictable performance results,
    • Phone time with our Chief Acoustic Engineer so any questions can be quickly answered,
    • Both horizontal and vertical diffusion options,
    • A perfect excuse to get away from the family chaos this holiday season,
    • Expert placement advice so you can get the most out of your completed unit,
    • A 100% money back guarantee!
  • acda 10 Activated Carbon Diaphragmatic Absorber Cherry wood image
    acda 10 Activated Carbon Diaphragmatic Absorber Cherry wood image

    Are you tired of muddy and sloppy bass in your room with bass notes masking your music into one big bloated mess? Want to mix without second guessing what you’re hearing? Then our Activated Carbon Diaphragmatic Absorber is for you!

    You get:

    • The most powerful low frequency absorber available in the world today,
    • 100% absorption at 50 Hz., 63% at 40 Hz. and absorption all the way down to 30 Hz., all in a depth of just 16″,
    • Unprecedented attack and decay clarity in every bass note, so you can mix without second guessing,
    • A bass absorber that softens the mids and the highs,
    • A solid wood unit that stands 30″W x 60″H x 16″D,
    • Independently tested and predictable performance results as verified in this report by Riverbank Acoustical Labs,
    • Phone time with our Chief Acoustic Engineer so any questions can be quickly answered,
    • Expert placement advice so you can get the most out of your completed unit,
    • A 100% money back guarantee!
  • Activated Carbon Diaphragmatic Absorber image
    Activated Carbon Diaphragmatic Absorber image

    Are you tired of muddy and sloppy bass on your sound stage with bass notes blurring and smearing into one big bloated mess? Tired of not connecting with your music the way you know it’s possible? Frustrated by the lack of an emotional connection with your songs despite investing a crazy amount of money into your amp, speakers and hi-fi?

    Imagine being able to hear incredible bass separation and definition in every piece of music you play and enjoying the sound of your music coming to life as your mids and highs pop like you always dreamt possible. Imagine being able to experience crystal clear attack and decay in each individual bass note in every piece of music you mix or listen to.

    With the ACDA-10, you’re going to feel the power of every single bass note the way you want to hear it. It’s that connection to the music which makes all the difference to your enjoyment of it. It’s the dynamics and separation of instruments with crystal clear clarity definition, which creates the spine tingling, hairs on the back of the neck sensation that you desire so much from your mixing efforts and music collection.

    If you order the ACDA 10 today you will also get:

    • A free 30 minute phone or video consultation on your room mode issues with me, the products inventor, Dennis Foley
    • A 100% risk free 30 day money back guarantee
    • And castors so you can move the units in and out of your room if your listening room serves multiple purposes.

Best Sellers

  • Mockup of DIY Acoustic Treatment build plans package
    Mockup of DIY Acoustic Treatment build plans package

    FLASH SALE – OFFER ENDS IN
    Only $27 instead of $149.95!

    Having problems with the acoustics in your room? Need a cost effective way of dealing with absorption and diffusion? Then our all in one DIY Build Plan package is for you!

    You get:

    • 7 DIY Build Plans in one great value deal.You get a Broadband Diaphragmatic Absorber to manage your low frequency problems, Acoustic Panel plans to manage your mids and highs and 5 Sound Diffuser build plans to make your small room sound larger!
    • Each plan comes with a material and tool list, cut sheet and easy to follow step by step assembly instructions,
    • Actual build photos showing you what each finished step looks like,
    • Your solid wood BDA Bass Absorber unit, when built, will stand 24″W x 48″H x 10″D and bass energy all the way down to 40 Hz!
    • 5 Sound Diffuser Plans included (Metric & Imperial!).
    • DIY plans that are based on our $1,000+ production units!
    • Independently tested and predictable performance results,
    • Phone time with our Chief Acoustic Engineer Dennis Foley so any questions can be quickly answered,
    • Both horizontal and vertical diffusion options,
    • A 100% money back guarantee!
    Sale!
  • Image of Acoustic Foam sheets
    Image of Acoustic Foam sheets

    Tired of working with dead sounding foam? Want your vocals and music to shine without losing their emotion and energy? Then our unique Acoustic Foam is for you.

    More cells with better shapes produce more absorption below 500 Hz. In fact, we absorb 30% at 125 Hz. and 63% at 250 Hz. reaching 100% at 500 Hz. We went after the bottom half of the existing absorption curves to produce a foam that has a smoother absorption curve that goes lower where our vocals start and ends with a smoother, more gradual rate and level of absorption.

    You get:

    • More absorption below 250 Hz. than standard foams. It absorbs 30% at 125 Hz., 63% at 250 Hz. and 100% at 500 Hz.
    • Smoother absorption curve from 125 Hz. – 500 Hz. than any other foam on the market. This range is the heart of your vocal and music frequencies.
    • Technology that manages side wall reflections so you can hear the direct sound from your sources and not the reflected energy of your room.
    • Box of 4 foam tiles
    • Available foam sizes: 25″ x 18.5″ x 2″ | 25″ x 54″ x 2″ | 37″ x 54″ x 2″
    • Studio foam that lets your vocals and middle range instruments pop.
    • A technology that does not drain the life out of your room like so many other foams.
    • Foam that finally lets you hear the intimate timbre of the singers voice in every recording. Finally you will have a room that is an acoustical pleasure to record in and very much in demand.
    • A foam that comes with variable installation options.

    ALL PRICES FOR A PACK OF 4 FOAM SHEETS.

  • Mockup of a Acoustic Panel Foam DIY Plan
    Mockup of a Acoustic Panel Foam DIY Plan

    Are you tired of homogenous, ugly looking foam stuck up on your walls? Need a cost effective way of dealing with the problem? Then our DIY Acoustic Panels are ideal for you!

    You get:

    • A material and tool list, cut sheet and easy to follow step by step assembly instructions,
    • Actual build photos showing you what each finished step looks like,
    • DIY plans that are based on our $350+ production units!
    • Phone time with our Chief Acoustic Engineer so any questions can be quickly answered,
    • A 100% money back guarantee!
  • image of Acoustic Treatment DIY Plan bundle
    image of Acoustic Treatment DIY Plan bundle

    If you’re looking for a complete DIY solution to your room problems, this DIY bundle is for you. It contains the full construction build plans for the QD-7 Sound Diffuser, Acoustic Foam Panels and our BDA Broadband Diaphragmatic Absorber all in one package.

    What you will get:

    • 3 professional DIY construction plans
    • Sound absorption from 40 Hz. – 400 Hz. (BDA)
    • Sound absorption from 125 Hz. – 7,500 Hz. (Foam Panel)
    • Sound diffusion from 850 Hz. – 3,400 Hz.
    • DIY plans that are based on our $1,000+ production units!
    • Independently tested and predictable performance results
    • Phone time with our Chief Acoustic Engineer so any
      questions can be quickly answered
    • Expert placement advice so you can get the
      most out of your completed unit
    • A 100% money back guarantee!
  • image of a QDA 13 Quadratic Diffuser Absorber from Acoustic Fields
    image of a QDA 13 Quadratic Diffuser Absorber from Acoustic Fields

    The QDA – 13 are two units within one. First, a quadratic diffuser based upon prime number 13 with a diffusion frequency response starting at 285 Hz. and going through 3,450 Hz. Behind the prime 13 quadratic diffuser is our activated carbon broadband low frequency absorber from 30 Hz. – 400 Hz. At the base of the QDA-13 is our more frequency specific carbon absorber from 30 Hz. – 50 Hz. The QDA measures 27″ w x 60″ h x 12″ deep and weighs 275 lbs.

    ACDA-10 Riverbank Test Result

    ACDA-12 Riverbank Test Result

    The Quadratic Diffusion in the QDA takes your sound and spreads it out across your room in the way nature intended you to hear it without your room getting in the way. Your room prevents this naturally occurring sound-field from happening because it has 4 walls, a floor, and a ceiling. Diffusion minimizes the reflections that want to destroy your precious direct sound from your speakers. Whilst reflections from room surfaces help you localize and define sound and distance, these reflections must be managed through diffusion so that the reflections do not get in the way of the sound coming from your speakers. This is why your ears are longer than they are wide.

    With the QDA you will finally get to experience the involvement that your expensive speakers are producing but which your room is stopping you from hearing. Through no fault of your own you have become so used to, and accepting, of poor diffusion in your room that your ears and eyes will open wide when you hear Quadratic Diffusion for the first time…Seriously, words fail to describe just what an impact diffusion has until you try it for yourself!

    If you order the QDA today you will also get

    • A free one 30 minute phone or video consultation on your room mode issues with me, the products inventor, Dennis Foley
    • A 100% risk free 30 day money back guarantee
    • And castors so you can move the units in and out of your room if your listening room serves multiple purposes.

On Sale

  • Mockup of DIY Acoustic Treatment build plans package
    Mockup of DIY Acoustic Treatment build plans package

    FLASH SALE – OFFER ENDS IN
    Only $27 instead of $149.95!

    Having problems with the acoustics in your room? Need a cost effective way of dealing with absorption and diffusion? Then our all in one DIY Build Plan package is for you!

    You get:

    • 7 DIY Build Plans in one great value deal.You get a Broadband Diaphragmatic Absorber to manage your low frequency problems, Acoustic Panel plans to manage your mids and highs and 5 Sound Diffuser build plans to make your small room sound larger!
    • Each plan comes with a material and tool list, cut sheet and easy to follow step by step assembly instructions,
    • Actual build photos showing you what each finished step looks like,
    • Your solid wood BDA Bass Absorber unit, when built, will stand 24″W x 48″H x 10″D and bass energy all the way down to 40 Hz!
    • 5 Sound Diffuser Plans included (Metric & Imperial!).
    • DIY plans that are based on our $1,000+ production units!
    • Independently tested and predictable performance results,
    • Phone time with our Chief Acoustic Engineer Dennis Foley so any questions can be quickly answered,
    • Both horizontal and vertical diffusion options,
    • A 100% money back guarantee!
    Sale!
FREE ROOM ANALYSIS
Call Us 520–392–9486
100% Money Back Guarantee